7/2/2023 0 Comments Wansview dvr.webcam![]() ![]() If you’re here from our post on Live Streaming Your IP and HD-TVI Security Cameras with OBS, you’ll know one way we use RTSP is to live stream cameras around our office in our Facebook dealer group! Getting the RTSP address to live stream is a super useful application, and this post will help you get that information. You can think of it as a handshake between the camera and whatever device is pulling the RTSP stream. Its primary uses are to pull a video feed from a camera to an NVR, viewing software, or even home automation solutions. RTSP allows you to pull a live video stream from your camera and view it from different devices and programs. cgi-bin/CGIProxy.RTSP stands for Real Time Streaming Protocol. ![]() Use the information returned by the above URL to create the override settings.Enable the motion alarm in the web interface of your camera and setup any areas you wish movement to be ignored in.This setting is called customMotionAlarmUrl and the steps to using it are: Some Foscam cameras need to have a detection area listed in the URL when you enable the motion alarm.Īs each Foscam model has a different resolution and two different URLs, this makes it difficult to automate, so an override feature was added to create your own "enable the alarm" URL.If your camera does not support MJPEG as some Foscams no longer do, then you can set mjpegUrl to contain ffmpeg to use your CPU to generate a MJPEG stream.This can be done by entering this into any browser: To use MJPEG streaming, you need to enable one of the streams to use this format.If the user/pass is wrong, the camera can lockout and refuse to answer the binding requiring a reboot of the camera, so be sure the details are correct before the camera tries to poll the camera too many times.# Dahuaįor MJPEG to work, you need to set the first sub-stream to use MJPEG format for the default settings to work, otherwise you can override the default with mjpegUrl config with a valid URL for MJPEG streams. The old alarm polling based method is used if you setup as amcrest, and the newer/better event based method is used if you setup as dahua instead.Īll other features should be the same between the two. It is better to always setup your Amcrest camera as a dahua thing type. These cameras do not have the ability to create H.264 streams and hence can not be used with HLS, however all other features should work.ĭue to many custom firmwares available, you may need to ask the firmware developer what the URLs are for snapshots and MJPEG streams if they have changed the defaults from what the Arduino IDE sample code uses.įfmpegOutput = "/tmp/Esp32Camera/", ffmpegInput = "" ] # Amcrest Some cameras allow the key frame to be created every second or a different amount by the user, refer to your cameras manual and support on how to do this. ![]() Snapshots generated by FFmpeg use the key frames (iFrames) to lower the CPU load, and since some cameras only produce a key frame every 2+ seconds with their default settings, this will effect how often a snapshot is produced. When using FFmpeg instead of a provided URL to create snapshots, it requires more CPU that you can turn on and off via the pollImage channel using a switch or rule. If your camera has a snapshot URL, provide it to the binding via the config called snapshotUrl after first testing the URL in any browser. This binding can turn a RTSP stream into snapshots (.jpg still pictures), create motion and audio alarms, cast the camera and much more.įFmpeg is required to be installed for these features to work and this must be done manually.įFmpeg can be installed very easily see Video Streams. # Special Notes for Different Brands # Generic Cameras Only after doing the above ask for help in the forum and create a new thread.Search the forum using any log messages to find how others have already solved it.To enable TRACE logging, enter this in the openHAB console log:set TRACE. Always look at the log files with TRACE enabled, as any FFmpeg and camera errors may not reach the INFO logs.Check if the camera is offline, if so there will be a reason listed.Check this readme for any setup steps for your brand.To see what features each brand has implemented from their APIs, please see this post: They usually have better picture quality and more advanced features compared to lower priced cameras. I recommend purchasing a brand of camera that has an open API, as many features use far less CPU when done with an API camera. This binding allows you to use most IP cameras in openHAB and has many hidden features, so please take the time to read through this guide to learn different ways to work with cameras that you may not know about. ![]()
0 Comments
Leave a Reply. |